1. Loosen your lug nuts, jack up the car safely and remove the tire. Knock the centercap out from the inside of the rim. You can pry the centercap off with the wheel on the ground but you risk damaging it. There is almost no way to damage it if you knock it off from the inside. After the centercap is knocked out, use your flathead screwdriver and carefully pry the notch out of the axle nut. Be careful doing this I broke two screwdrivers. Here is a picture of the axle nut.



2. Great, now put the wheel back on the car and just snug up the lug nuts. Put the car back on the ground and grab your breaker bar, an extension, and the massive axle nut socket. Get that baby in there and break the 134 ft/lbs of seized on torque off the nut free. If you can't get the nut free this way, you will need an impact gun. Here is what the socket looks like passing through the rim:



3. Great, now take your stupid wheel back off the stupid car ( a bit repetative I know, if you have access to air tools you can remove the axle nut with the wheel off to begin with which makes it a lot easier. ) After the wheel is removed take these two 17mm bolts off of the caliper, and hang it up out of the way all nice like. DO NOT REMOVE THE BRAKE LINE BOLT!!!:




4. Now, remove the two 22mm nuts off the strut assembly, these are attached at 71ft/lbs and are probably seized a bit so it might be a bit of a battle to get them out. LEAVE the bolts on, you will need them there to break the balljoint free from the lower control arm:




5. Now your well on your way, and it's time to remove the vehicle speed sensor. This was a ROYAL bitch because I was terrified to destroy the sensor and it was seized in. Remove the 10mm bolt, then I ended up having to get a pair of vice grips and attached them tightly to the sensor. Then I slowly started to spin the sensor until it came free. DO NOT disconnect the sensor connector, remove the entire sensor as a whole



6. Now you have to remove the cotter pin off the 17mm castle nut. You can cut it off or pry it straight with plyers and pull it out. Even if you manage to "Save" the cotter pin, use a new one. It should have come with the ball joint anyway. Here is a picture of the castle nut before and after removal.




7. Now its time to break the balljoint free from the lower control arm. There is a very simple method to doing this that will save you LOTS of time if you do it this way. It involves your hydraulic jack and a ratchet. What you do is jack up the lower control arm until you can fit a ratchet between the knuckle and arm itself:



8. Fit the ratchet inbetween the LCA and knuckle.



9. After its in place, simply lower the jack all the way down and you will hear a "POP" sound. If you look the ball joint should be seperated from the control arm:



10. Now you can use a hammer to drive the axle (spindle) back into the knuckle, you can use a regular hammer as long as you don't smash on it. You really shouldn't have to hit it very hard. If you cant get the axle fully out from behind you can get it when you remove the last two bolts off the knuckle.

11. Great, the hard part is done, now you can remove the two bolts from the strut assembly. Sorry this picture is a little bit fuzzy but its basically the two bolts that you removed the nuts from earlier. You can tap them with a hammer to get them out. Just don't go buck wild and mess up your threads.



12. The knuckle will want to come out easilly, but you might have to hammer the lower ball joint upwards a little bit to actually remove it from the car. This is where a second person comes in handy, but it can be done by one person. So your kinda doing three things at once here, making sure the axle is fully clear of the knuckle, making sure the balljoint is coming out of the lower control arm nicely, and balancing the knuckle to make sure when it comes free you don't drop it. Great, now the knuickle should be out of the car.



13. Hold the knuckle in your hand with a smile. If you can accomplish this you can do most suspension work on the front end of a honda civic yourself. Anyway... here it is:



14. Now to press the ball joint out with your fancy *** tool. This is where an impact comes in VERY handy but you can do it with a ratchet. You look at the tool and it looks pretty confusing. Luckilly, you only need a few of the pieces that come with the tool. You have to make sure you select an adapter that will allow the ball joint to "Push" out and an adapter does not sit flat up against the knuckle, it should actually sit up against the flat piece on the bolt of the ball joint. It's very hard to explain but hopefully you get it. It should look like this to remove the ball joint:



15. I cheated and used my impact even though this is an air tool free guide, but I have done it with a ratchet, as you can tell I'm messy as hell:



16. You should have no problem pressing the ball joint out with this method, it might take a little bit of time and a little bit of muscle. A vice would help a lot to keep things stable if your not using air. Pressing in the ball joint is pretty much the exact opposite, just make sure you put a **** ton of anti seize paste on the knuckle where the ball joint will seat. The push side has to be up against the flat part of the ball joint. You can actually attach the C clamp right to the ball joint, it fits well. Make sure you select an adapter on the bolt side that allows the joint to slide through fully. You know the ball joint is fully seated when it sits flush up against the knuckle. Some aftermarket joints like the one I got come with rings, you have to insert the rings into the groove on the ball joint on the bolt side. Use the two little holes and insert a pair of needle nose pliers into them, then spread the rings apart and fit it into the groove. It's a royal pain in the *** and it's nice to have two people for this. It's doable by yourself It should look something like this when you are finished pressing it in:



17. I forgot to take a picture of the ball joint installed on the knuckle so I stole one from the other DIY guide, sorry greeen01civic4d



18. Your done, reassembly is very very very very simple and easy. To put the knuckle back on you insert the ball joint into the lower control arm first, then guide the spindle back through the bearing. After that you can seat the upper portion of the knuckle into the lower strut assembly. Once the knuckle is lined up to the bolt holes and the axle is through, you can put the two 19mm lower strut bolts back in and torque the 22mm nuts to 71ft/lbs. Don't forget to apply your anti seize lube on the threads:



19. Lube the hole where the vehicle speed sensor goes with anti seize paste and torque the 10mm bolt to 7.2ft/lbs.



20. Put anti seize paste on the ball joint threads that are sticking through the lower control arm. The castle nut does not have a torque spec it has a torque range. You have to do your best to line up the holes for the cotter pin and still get it within that torque range. The range for the 17mm castle nut is 43-51ft/lbs. I had major issues with this because when hand tight one of the ball joint castle nuts was way past the holes for the cotter pin already. This was a major pissoff so I redid the balljoint with the same result. I ended up putting a washer on it to make the holes line up as I'm afraid to lose the castle nut. I called a mechanic shop and they said it was O.K. Here is a picture of the final result, you can see the washer above the nut:



21. Now to reinstall the caliper. Just carefully slide the caliper onto the rotor and install (after anti seizing) the two 17mm bolts on the back and torque them to 80ft/lbs.



22. Put antiseize on the end of the axle(spindle) and snug up the new axle (spindle) nut on the end of the axle. Now, with your centercap still off your rim, reinstall the tire and snug up the lugnuts. They don't have to be torqued on just yet, lower the car down on so its on its own weight and torque that baby to 134ft/lbs. After torqued grab your flathead screwdriver and smash the end of the nut into the little groove. It should look something like this whe finished:



23. Now you can torque your wheels back on to 80ft/lbs, install your centercap and call it a day. 

I tried to make this as comprehensive as possible so anyone can do it. Unfortunatly my camera died halfway through so the actual removal of the knuckle isnt shown that well in pictures. Hopefully this helps you complete your ball joint replacement

Make sure you have the two strut bolts in place when you are doing it. I spent a lot of time on the first one only to realize that it won't work without the strut bolts there. If that doesn't work you need to use the puller.

SO.. Make sure these two are still in:



And the ratchet is like this:



Drop the suspension down. Sometimes you may have to put your foor ontop of the rotor and push down with some force to break it free. You need to jack up the LCA to get the ratchet in there. And release the jack at full speed to make sure you have the most ball joint release force you can.

DIY on removing Ball Joints

Submitted by xxx@******.com

Revision 2
Article submitted on 4 Jul 2013
Last modified on 4 Jul 2013
Viewed 3724 times