MODELS:
1999 - 2002 (AB) Ram Van/Wagon
1999 - 2002 (AN) Dakota
1999 - 2002 (BR/BE)Ram Pickup
1999 - 2002 (DN) Durango
2002 (DR) Ram Pickup
2001 - 2002 (JR) Sebring Sedan/Stratus Sedan/Sebring Convertible
2002 (KJ) Liberty
1999 - 2002 (LH) Concorde/Inytrepid/LHS/300M
1999 - 2000 (NS) Town & Country/Caravan/Voyager
1999 - 2002 (PL) Neon
1999 - 2002 (PR) Prowler
2001 - 2002 (PT) PT Cruiser
2001 - 2002 (RS) Town & Country/Caravan/Voyager
1999 - 2002 (WJ) Grand Cherokee
1999 - 2001 (XJ) Cherokee

NOTE: PLEASE READ INSTRUCTIONS FULLY BEFORE ATTEMPTING
TO PROGRAM TRANSMITTERS.

Program Method A (Customer Program Method)

1. Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2. Turn ignition to run position. (Allow ignition chimes to stop).
3. Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and
release (a short chime will sound for AN/DN).
6. Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).

NOTE: (FOR DR 0NLY ) A CHIME WILL NOT SOUND ON STEP #6 FOR
THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON
PROGRAMMING THE SECOND TRANSMITTER.

7. Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OFF position. Transmitter programming mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).

Program Method B (Customer Program Method)

1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2. Turn ignition to the run position (Allow ignition chimes to stop).
3. Using original transmitter, press and hold the [UNLOCK] button on the
transmitter for between 4 and 10 seconds.
4. Continue to hold the [UNLOCK] button and press the [PANIC] button. A
chime will sound to indicate that the transmitter programming mode has been entered (Allow 3 seconds for chime to sound).
5. Press a button on all transmitters to be programmed into the system
including any previously programmed transmitters; a chime will sound when each transmitter has been programmed.
6. Turn the ignition to OFF position to exit the transmitter programming mode.

Program Method C (Dealer Program Method) *Can be used for any type transmitter.

1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt
to function transmitter, if working as designed discontinue programming.
2. Turn ignition to the run position (Allow ignition chimes to stop).
3. Plug DRBIII to vehicle’s 16–way data link connector.
4. Follow Service Manual and DRBIII instructions to program transmitters.

Program Method D (For use with AB vehicles not equipped with VTSS only)

1. Locate the dark green program enable wire connected to pin #1 of the 16-way data link connector under the left side of the instrument panel.
2. Connect the program enable wire terminal to a good ground.
3. Insert the key into the ignition and turn the ignition switch to the ON position. The power locks will cycle (Lock and Unlock) indicating that program mode has been entered.
4. Using the transmitter to be programmed, press either [LOCK] or [UNLOCK]. The power locks will cycle indicating the transmitter has been programmed successfully.
5. Repeat step 4 to program additional transmitter.
6. Disconnect the program enable wire from ground to exit program mode.
7. Turn the ignition to the OFF position and remove the key.

============

I'm sure someone will make good use of this info.

V

0 total comments, spanning 0 pages.
Showing 0 to 0
Sign in to make a comment.


Submitted by xxx@******.com

Revision 0
Article submitted on 2 Mar 2015
Viewed 3718 times

Please enable / Bitte aktiviere JavaScript!
Veuillez activer / Por favor activa el Javascript![ ? ]